Top 10 typical forklift crashes ， forklift procedure need to take notice of these issues ！.

Don't undervalue the forklift at work. If the operation is not good, there will be severe crashes in mins, and there are lots of accidents including forklifts.

Instance 1: The forklift cargo obstructed the driver's sight, and the person in front might not be discovered, leading to a rolling mishap.
Situation 2: In order to preserve the balance of the forklift when lifting heavy goods, the staff members utilized their body weight as the weight, which virtually created casualties.
Instance 3: The size of the forklift cargo exceeds the allowable size of the course and holds on the roadside shelf, which practically causes an crash.
Instance 4: Forklift is speeding up and rolls over during a turn.
Instance 5: The forklift vehicle driver did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the employees unlawfully, the forklift motorist does not wear the safety belt, the forklift lifter drops and the chauffeur is crushed when the forklift surrender.
Situation 7: The forklift chauffeur did not put on a safety belt and fell from the vehicle when it surrendered and was crushed.
Forklift procedure must focus on these matters ：.

Beginning.
1. Before beginning, observe the environments, and after confirming that there are no barriers that impede the safety of driving, beep the horn first and afterwards start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be safe before beginning.
3. When the forklift starts with a lots, the chauffeur should first validate that the tons is secure and trustworthy.
4. The start needs to be slow and consistent.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be kept at 300mm-400mm, and the mast needs to be tilted backwards. .
2. Do not raise the fork too expensive when driving. When getting in and leaving the job site or while driving, take care that there will be no challenges overhead. When the load is traveling, the fork needs to not be elevated too high, which will certainly influence the stability of the forklift. .
3. After discharging, the fork must be decreased to the normal driving setting prior to driving. .
4. When transforming, if there are pedestrians or vehicles nearby, the driving signal must be released initially. High-speed sharp turns are restricted. High-speed doglegs will certainly create the vehicle to lose lateral stability and topple. .
5. When the forklift is downhill, it is purely restricted to turn off the flame and slide, and it is forbidden to brake unexpectedly while driving with lots unless there are unique circumstances.
6. When the forklift is running, it must obey the web traffic rules in the factory and should keep a certain security distance from the car in front. .
7. When the forklift is running, the tons needs to remain in the lowest setting that does not impede the driving, and the gantry must be appropriately slanted back. The tons shall not be increased except when stacking or loading. .
8. The elevation of the lots have to not obstruct the motorist's view. In special situations, when the item affects the forward vision, drive at a reduced rate when turning around.
9. It is prohibited to turn on the ramp, nor to drive throughout the ramp. .
10. The secure driving rate of the forklift in the factory area is 5 km/h, and it must drive securely at a reduced speed when entering the manufacturing workshop location. .
11. When the forklift is lifted, lifted or driven, it is restricted for workers to base on the fork to hold items and play a stabilizing function. .
12. If problems are found, they will certainly be repaired and reported in a timely Electric Forklift Truck for Warehouse way, and they will never ever run with diseases or hide them.

packing and discharging.
1. When fork-loading items, the range between both forks must be adjusted as required to make the tons of the two forks well balanced and not skewed, and one side of the thing must be against the shelf. .
2. It is forbidden to collaborate with a single fork or use a fork top or draw. In special conditions, security indication should be established to remind bordering pedestrians. .
3. In the process of packing and dumping products, the forklift must be stopped with the brake. .
4. The rate of the lorry must be slow and consistent. Be careful not to roll the wheels on the dunnage, so as not to stretch the rolled things and harm individuals. .
5. Electric Forklift Truck for Warehouse When using a fork to fork the goods, the fork must be as deep as possible under the tons, and it needs to be noted that the fork idea should not touch other items or objects. The tons should be supported with marginal back tilt of the gantry so that the tons does not glide in reverse. The mast can be tilted onward slightly when the tons is reduced to permit easy placement of the lots and removal of the forks. .
6. It is forbidden to fork products at broadband and ram hard items with the fork head. .
7. When the forklift is functioning, it is restricted for individuals to stand around the fork, so as to prevent the collapse of the goods and harm individuals. .
8. Straining is prohibited, and it is forbidden to make use of forks to raise employees to engage in high-altitude operations to prevent high-altitude falling mishaps. .
9. It is not permitted to make use of the brake inertia to slide, place, round or roll things. .
10. It is not allowed to use forks to pick, turn pallet unload.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork are in the air. Before leaving the forklift, you need to discharge the goods or reduced the fork framework.
2. Draw the hand brake take care of to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique conditions, such as the driver does not leave the vehicle's line of sight and does not exceed 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance should be examined, and gas, lubing oil and cooling water ought to be added.
2. Check the safety efficiency of beginning, running and stopping.
3. Inspect whether the lights and horn signals are complete and effective.
4. During the procedure of the forklift, examine whether the stress and temperature are normal.
5. After the forklift is running, the exterior leakage ought to also be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine before leaving the vehicle;.
2. When you encounter a person before you during driving, you need to send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m in the air;.
5. The transforming should not be also sharp to avoid the tendency of " cost-free switching";.
6. Running up and down the incline ought to be slow-moving and uniform, and no turning on the incline is allowed.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the lorry ought to be driven backwards when declining;.
8. When the forklift personnel lug the goods and move forward, if they run into large or hefty goods and most likely to the driver's line of vision, they should take the turning around workout
.
The "Eight Prohibitions" ought to be adhered to in the operation.
1. Solitary fork operation is not enabled.
2. It is not permitted to lift the goods for cross country driving.
3. It is not enabled to grab the goods by handing over the pallet with the fork.
4. It is not permitted to straight shovel chemicals, flammables and various other harmful chemicals with forks.
5. It is not permitted to utilize inertia pressure to pick up the goods.
6. It is not enabled to make use of braking force to expatriation round or easy-to-roll things.
7. It is not allowed to bring people to work with the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is increased.
8. Do not drive side to side on slopes
.
Car park is not allowed under the following conditions.
1. Curves, slim roadways, train crossings;.
2. Areas with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the very same length as the obstacle ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844